12 Years manufacturer Hot Selling for High quality factory Carbon Steel/ Stainless Steel Square Nut (DIN557) Factory for Nairobi in Switzerland in Zurich

12 Years manufacturer
 Hot Selling for
 High quality factory
 Carbon Steel/ Stainless Steel Square Nut (DIN557) Factory for Nairobi
 in Switzerland
 in Zurich

Product Detail

Product Tags

We support our buyers with ideal high quality products and high level service.Becoming the specialist manufacturer in this sector,we have gained rich practical experience in producing and managing.Our 12 Years manufacturer Hot Selling for High quality factory Carbon Steel/ Stainless Steel Square Nut (DIN557) Factory for Nairobi in Switzerland in Zurich, items won certifications with the regional and international primary authorities .For far more detailed information,please contact us!





  • Replace The Speaker

    To replace the speaker on bObsweep Pethair Plus, you will need a Phillips head screwdriver, a flat head screwdriver, and a new speaker.

    Before starting any repair on Bob, turn his side power switch OFF and remove his dustbin.

    Then, flip Bob over onto a flat surface and remove his main and side brushes using the flat head screwdriver.

    Keep all removed screws and parts safely aside, as they may be needed for later reassembly.

    Use a Phillips head screwdriver to remove the 6 screws on Bob’s underside that hold him together.

    One screw on each side of the front wheel. One screw to the right of the main brush motor.

    One screw on each side of the dustbin. The final screw is in the brush compartment.

    Bob’s cover is no longer secured, so hold the top and bottom together as you carefully flip him back onto his wheels.

    Grip Bob’s cover from the back and lift up to expose the mainboard.

    Slide the power inlet down and tuck it somewhere safe to avoid compressing its wires.

    To detach Bob’s cover completely, disconnect 4 circuit plugs:

    Two at the lower edge of the mainboard, near the wheels.

    And two more at the top edge, near the bumper.

    Bob’s cover is now completely detached and can be set aside for the rest of the repair.

    Before you can gain access to the speaker, you must first remove the mainboard and side brush motor.

    Disconnect all remaining 12 circuit plugs from the mainboard. Press the small tab on each circuit plug and pull to disconnect.

    Remove 3 screws on the mainboard. Keep them aside for later reassembly. Now lift the mainboard out of Bob.

    In front of Bob’s right wheel you’ll see the side brush motor, held in place by 3 screws.

    Remove all 3 and keep them aside for later reassembly.

    Then, lift the motor out.

    Now that the speaker is accessible, simply lift it out of its space.

    Then lay the speaker in the circular groove inside Bob.

    Place the side brush motor in the open space, in line with the screw posts.

    Push down until the motor sits flat. Then reinstall all 3 screws. Feed the the motor’s wiring so it reaches over to Bob’s left side before replacing the mainboard.

    Align the holes in the mainboard with the 3 screw posts on Bob’s interior.

    Ensure that the mainboard sits flat before re-installing the 3 screws.
    One screw goes in the middle of the mainboard, one in the top corner, And one in the lower corner.

    Now reconnect all the circuit plugs correctly.

    The order of plugs on the left side of the mainboard, from top to bottom, is:
    A small plug with black and yellow wires.
    A plug with two pairs of twisted wires
    A plug with multi-colored wires for Bob’s left wheel,
    A plug with blue and black wires.

    The order of plugs at the top of the mainboard, from left to right, is:
    A small plug with red and green wires
    A wide plug with multicoloured wires,
    Two empty spaces for now
    And a small plug with black and orange wires in the top right corner.

    The order of plugs on the right side of the mainboard, from top to bottom is:
    A wide circuit plug for Junior’s power switch,
    And a plug with black and orange wires for Junior’s power inlet.

    For now, the bottom of the mainboard will have two open spaces on the very left.

    Then, the order from left to right is:
    A small circuit plug with a red wire,
    One more open space,
    A small plug with yellow wires,
    And lastly, a plug with multi-colored wires on the very right.

    Now you’re ready to begin re-attaching the cover.

    Reattach all 4 circuit plugs connecting Bob’s cover to the mainboard.

    2 connect to the top edge of the mainboard, and 2 more that connect to the bottom edge.

    Remember to slide the power inlet back into its space on Bob’s cover.

    Align the cover’s edges precisely. Then, flip Bob over onto a flat surface.
    Ensure that no wires are compressed in the main brush compartment or visible at the edges of the bumper.

    If so, take a step back and lift the cover to tuck the wires into the appropriate spaces.

    Once the wires are all safely tucked away and Bob’s cover is aligned properly, reinstall all 6 screws previously removed from Bob’s underside.

    Install the main and side brushes using the flat head screwdriver.

    Replace the dustbin before your next use and congratulations! You’ve just replaced Bob’s speaker. Happy Cleaning!



    Check out our tutorial videos (https://goo.gl/MK4JWp ). You will discover the world of Ambrovit screws and find the ons that fit your needs.
    All rights reserved. Unauthorized reproduction, copying, distribution or any other use of the whole or any part of the contents of this portal is strictly prohibited.

    The concrete screws with cylinder head TX 30 are ideal to be used on concrete, full masonry or perforated bricks, for the fixing of doors and windows in aluminium, PVC and wood, without using blocks or chemical compounds. The screws are made of carbon steel, with galvanized finishes. The ending part is threaded HI-LO. They have obtained the GOST R certification.
    The concrete screws are available in stock, in more than 50 different items.

    Ambrovit Bolts and Screws

    The Ambrovit company, set up in 1997, is today a leading player in Europe in fastening systems.
    The wide range of Ambrovit bolts and screws , that can be viewed on the online catalogue (link), is always available in our wide warehouse, where over 44.000* products pallets can be stored.
    The certifications D.o.P, GOST R, ETA CE of the Trento University testify the quality and reliability of Ambrovit, offering deliveries throughout Europe in 24/48 hours.

    To learn more about Ambrovit and its products, visit its website ambrovit.com

    Related Products

    WhatsApp Online Chat !