Manufacturer for Online Manufacturer for Wholesale Price China Small Hexagon Nut sale to Grenada Factory from Swiss Supply to Stuttgart
We support our buyers with ideal high quality products and high level service.Becoming the specialist manufacturer in this sector,we have gained rich practical experience in producing and managing.Our Manufacturer for Online Manufacturer for Wholesale Price China Small Hexagon Nut sale to Grenada Factory from Swiss Supply to Stuttgart, items won certifications with the regional and international primary authorities .For far more detailed information,please contact us!
Goods Lift UK Goods Lift Stainless Steel
APPLICATION Lifting goods between levels
PIT INSTALLED YES
CONSTRUCTION High Lift Scissor Table
MODEL / TYPE RLXY3-20/430-2C
CAPACITY 2000KG — evenly distributed load
TRAVEL / STROKE 4400mm (limit switch set at 4300mm)
CLOSED HEIGHT 750mm – pit dimensions to be advised at PDI
TOTAL RAISED HEIGHT 5050mm
PLATFORM SIZE 2200mm long & 1790mm wide, with anti slip surface (tear plate)
OPERATION 2,3 kW compact electro-motor with hydraulic pump unit and adequately sized oil tank wired to IP55 Standard. Power unit is located outside the Lift
POWER SUPPLY 400 Volts, 3 phases, 50 Hz
CONTROL VOLTAGE 24 Volts with IP55 insulated electrics
TRAVEL SPEED Approximately 75 seconds to maximum height
CYLINDERS Normally single acting precision made units complete with pipe break valve to prevent a rapid lowering speed in the unlikely event of a hydraulic hose failure. Delfleet anti corrosion, ETCH-Primer.
WEIGHT Approximately 1500KG’s
STANDARD FINISH Stainless Steel AISI304 platform, gates and handrails Mild steel RAL 9005; base frame and scissors Mild steel; axles, wheels and bolts
CONTROLS Two (2) constant pressure UP & DOWN hand control units with EMERGENCY STOP button and 6 meter long cable
SAFETY TRIP BAR Aluminium safety frame with built in safety function. If the safety frame is touched on its way down, the Lift stops immediately. To continue lowering, the table has to be raised a little to be able to lower again.
MAINTENANCE Standard safety legs are provided to support the scissor lift mechanism in the raised position and must be deployed for all servicing and maintenance work
INSTALLATION Fitted with lifting eye bolts for easy installation in pit if required
HAND RAILS 1100mm high hand rails with 150mm high kick-boards, fitted to both long sides and one short side
SAFETY GATES 1100mm high twin safety gate with 150mm high kick-boards fitted to one 1500mm side — outwards opening
INTERLOCKING GATES The safety gates are interlocking into the control system of the lift so the platform will NOT raise or lower when the gates are open
OTHER Landing legs and lift eye bolts for installation
EN 1570 A Declaration of Conformity or Incorporation is issued with every
Lift unit stating they have been manufactured to meet all requirements of current European Standards for scissor lifts
GENERAL The lift is designed to operate on a firm even floor surface
Goods Lift Table will be supplied with a remote power pack for ease of change over, should a fault occur. A spare power pack will also be provided.
Supplied with a four sided enclosure to both levels measuring 2.50m long x 2.09m Wide – Manufactured in 304 grade stainless steel and finished with a silicone bead blast (to give an even matt finish to the stainless steel)
Ground floor: 3900mm high to the underside of the mezzanine floor. Incorporating a 2000mm high gate to one short side.
First Floor: 2100mm high. Incorporating a 2000mm high gate to one short side
Both gates will be fitted with electro-mechanical interlocks to prevent platform motion if either gate is open and to prevent the gates from being opened unless the platform is at the appropriate level.
Manual Handling Solutions MHS.COM Ltd provides some of the most advanced handling equipment available from standard products to a bespoke solution. Our range of lifting equipment and materials handling products are by far the most sophisticated and technically advanced and manufactured to the highest standard. As a Handling Solutions provider our goal is to work closely with our customers and bring the most technically advanced handling products – solutions to market.
Manual Handling Solutions (MHS.COM Ltd)
58, Paige Close
Watlington, King’s Lynn,
Norfolk PE33 0TQ UK
Tel 01553 811977
Note for the purpose of taking videos the safety systems was disconnected.
we are professional to provide all kinds of non-standard metal parts,precision CNC turning parts, automatic lathe parts, precision non-standard screws ,nuts, rivets, washers, stamping parts and other hardware products. Materials include stainless steel, carbon steel, copper, brass, iron, aluminum and various kinds of steel. Products are widely used in electronics, hardware, lighting, toys, sanitary ware, furniture, medical, sports equipment and other industries. We passed the ISO9001: 2000 quality system certification, We can provide free design of product, development, process improvement and other technical problems.Our products are selling well both domestic and abroad .